DISC SPRINGS · BELLEVILLE WASHERS

Disc Springs to GB/T 1972 — Series A / B / C

High load in a small axial space. 90 standard sizes from Ø8 to Ø250 mm, manufactured from 50CrV / 51CrMnV / 60Si2Mn spring steel per GB/T 1222.

Load / space ratio

A disc spring develops several times the axial force of a coil spring in the same envelope — ideal for bolt pre-load, valves and overload protection.

Three standard series

Series A (D/t≈18) for high load, Series B (D/t≈28) the balanced workhorse, Series C (D/t≈40) for large travel — all to GB/T 1972.2-2023 Annex B.

Stackable

In series for travel, in parallel for load, in combination for both — one washer geometry covers a wide force/deflection map.

Real product photos

Actual parts photographed from our supply base — disc springs and ring spring stacks in phosphated spring steel.

Disc spring stack — parallel stacking for higher load
Disc spring stack — parallel stacking for higher load
Single disc spring (Belleville washer), phosphated finish
Single disc spring (Belleville washer), phosphated finish
Ring spring stack assembly
Ring spring stack assembly
Ring springs — two assembled stacks
Ring springs — two assembled stacks

Standard size range

SeriesD/th₀/tOuter diameter DCharacter
A≈ 18≈ 0.408 – 250 mmHighest load, small deflection
B≈ 28≈ 0.758 – 250 mmBalanced — most widely used
C≈ 40≈ 1.308 – 250 mmLarge deflection, lower load

Source standard: GB/T 1972.2-2023 Belleville springs — Part 2: Technical requirements (data transcribed from Annex B). Material steel per GB/T 1222.

Send us your load, deflection and space envelope — we return a series/stack recommendation with standard sizes.

Get a recommendation

Before You Order: Six Checks

You do not need to read all 90 dimension rows first — run through these six points in order and your requirement is clear.

1 · Load and deflection
The force you need (F) and the travel you need (s) come as a pair — a disc spring gives one with the other. Standard rating F₁ is quoted at H₁ = H₀ − 0.75 h₀.
2 · Size envelope
Measure the OD, ID and installed height available. Series A (D/t ≈ 18) gives highest load, B (≈ 28) is the balanced workhorse, C (≈ 40) gives the largest travel at lower load.
3 · Stacking arrangement
Single, opposed (in series — travel adds up), or stacked in parallel (force adds up). Mixed stacks tune the load–deflection curve; each layer changes calculated height.
4 · Stress and fatigue
Check the calculated stress at the working point against the allowable σOM ≤ 1600 MPa. For millions of cycles, keep the working range away from full flattening.
5 · Material and temperature
Standard steel is 50CrV / 51CrMnV / 60Si2Mn (Group 1: 425–510 HV10, Groups 2 & 3: 42–52 HRC). Confirm the operating temperature before quoting hardness and set treatment.
6 · Installation and guidance
Springs need flat, parallel bearing faces and either a guide rod or sleeve. Confirm the preload, the clearance for OD growth under load, and the assembly direction of stacked sets.

Not sure about one of them? Send the load, the space available and a sketch — we size the spring and quote against your data. Send your requirement →

Ordering & Delivery

Send your size list (D / d / t / h₀) and the quantity you need — we confirm the lead time for that exact combination before you commit.

Warranty1 year
Payment100% before shipment
Lead timeConfirmed per model and quantity

Get a Quote

Talk to an engineer

Send us the specification you need — dimensions, voltage, operating temperature, quantity. We answer within one working day.