GB/T 1972.2-2023

Technical Requirements & Quality Conditions

Material, manufacturing, hardness, tolerances and allowable stress — the conditions every certified disc spring must satisfy.

Material (cl. 6.1)

Spring grade steels 50CrV, 51CrMnV and 60Si2Mn per GB/T 1222-2025. Strip per GB/T 3279 / YB/T 5058; forged stock (forging ratio ≥ 2) per GB/T 1222. Every heat comes with a mill certificate and is re-checked before use.

Manufacturing routes (cl. 6.2, Table 4)

GroupThickness tTypical process chain
10.20 – 1.25 mmBlanking → cold/hot forming → edge rounding (fine-blanked edges: b₁/t ≤ 15 %, polished band hs/t ≥ 75 %)
21.25 – 6.00 mmBlanking → forming → machining of D/d → edge rounding → heat treatment; or machining of supporting surfaces after heat treatment
36.00 – 14.00 mmHot forming → full machining → edge rounding, or blanking → machining → heat treatment

Hardness (cl. 6.5.1)

Group 1: 425–510 HV10. Groups 2 and 3: 42–52 HRC. Special hardness windows by agreement.

Decarburization (cl. 6.5.2)

After quench and temper, total decarburized depth per side ≤ 3 % of thickness (max 0.15 mm). For t ≤ 0.3 mm, ≤ 0.01 mm. Hardened no more than twice.

Set (pre-stress) treatment (cl. 6.6)

After heat treatment, springs are pressed at least twice the test load Fₛ to flat, producing controlled permanent set that stabilizes load and improves relaxation behaviour.

Surface treatment & shot peening (cl. 6.7–6.8)

Phosphating or equivalent; electroplating is discouraged (hydrogen embrittlement). Shot peening per GB/T 31214.1 when specified for fatigue duty.

Allowable stress (cl. 6.9)

Static duty: computed stress at OM position when fully flat, σOM ≤ 1 600 MPa (above that, σ₁ ≤ 3 000 MPa per GB/T 1972.1). Dynamic duty: minimum pre-deflection s ≈ 0.15–0.20 h₀ avoids position-I cracking; life is verified against the 10⁵ / 5×10⁵ / 2×10⁶ cycle diagrams.

Tolerances

Thickness, D/d (class I or II), free height and test-load tolerances per Tables 5–8 of the standard; e.g. thickness tolerance ± 0.03/− 0.06 mm (group 1, t ≤ 0.6) down to ± 0.15 mm (group 3). Concentricity 2×IT11 (class I) or 2×IT13 (class II).

Source standard: GB/T 1972.2-2023 Belleville springs — Part 2: Technical requirements (data transcribed from Annex B). Material steel per GB/T 1222.

Need a certificate-backed data sheet for your application?

Talk to us

Before You Order: Six Checks

You do not need to read all 90 dimension rows first — run through these six points in order and your requirement is clear.

1 · Load and deflection
The force you need (F) and the travel you need (s) come as a pair — a disc spring gives one with the other. Standard rating F₁ is quoted at H₁ = H₀ − 0.75 h₀.
2 · Size envelope
Measure the OD, ID and installed height available. Series A (D/t ≈ 18) gives highest load, B (≈ 28) is the balanced workhorse, C (≈ 40) gives the largest travel at lower load.
3 · Stacking arrangement
Single, opposed (in series — travel adds up), or stacked in parallel (force adds up). Mixed stacks tune the load–deflection curve; each layer changes calculated height.
4 · Stress and fatigue
Check the calculated stress at the working point against the allowable σOM ≤ 1600 MPa. For millions of cycles, keep the working range away from full flattening.
5 · Material and temperature
Standard steel is 50CrV / 51CrMnV / 60Si2Mn (Group 1: 425–510 HV10, Groups 2 & 3: 42–52 HRC). Confirm the operating temperature before quoting hardness and set treatment.
6 · Installation and guidance
Springs need flat, parallel bearing faces and either a guide rod or sleeve. Confirm the preload, the clearance for OD growth under load, and the assembly direction of stacked sets.

Not sure about one of them? Send the load, the space available and a sketch — we size the spring and quote against your data. Send your requirement →

Ordering & Delivery

Send your size list (D / d / t / h₀) and the quantity you need — we confirm the lead time for that exact combination before you commit.

Warranty1 year
Payment100% before shipment
Lead timeConfirmed per model and quantity

Get a Quote

Talk to an engineer

Send us the specification you need — dimensions, voltage, operating temperature, quantity. We answer within one working day.